# Box Truck Repair for Eastvale, California > Corner post, panel, floor and roll up door repair on box trucks running Eastvale delivery and moving routes. Source: https://ocrv.info/vehicles/commercial-trucks/box-truck A box truck carries an enclosed cargo body on a medium duty cab and chassis, usually with a roll up rear door and a hardwood floor. Repair work covers corner posts, side panels, roof bows and skin, rear frame and door track, floor replacement, liftgate mounting, scuff bands and cab collision and refinish work. ## Pricing Typical range $1,500 to $50,000+, 10 to 250 hours. Box bodies are built to a formula that has not changed much in decades. Vertical posts at intervals along each side, horizontal rails at the top and bottom, roof bows across the top, skin on the outside and plywood or hardwood on the floor. That construction is durable and, importantly, repairable section by section, which is why a box body typically outlasts two chassis if it is maintained. Damage arrives from three directions. Overhead strikes crush the front roof edge or tear the roof skin. Side contact in alleys and parking structures bends posts and splits skin along the seam. Loading operations beat up the rear frame, the door track and the threshold. On a truck used for moving or route delivery, the interior takes a fourth kind of damage from cargo shifting against the walls and floor. Fleets and owner operators around Eastvale run these on I-15, SR-60 and surface routes daily. The truck comes roughly twenty miles to the Yorba Linda facility and everything happens in shop: post replacement, skin work, floor replacement, door rebuilding, liftgate mounting repair and refinish. Scope is body, paint, structural and equipment installation. Engine and drivetrain service is not performed. ## Common damage - Crushed front roof edge from overhead strikes - Bent side posts with split skin - Distorted rear frame and door track - Bent roll up door slats - Rotted hardwood floor at the rear threshold - Cracked liftgate mounting welds - Corroded crossmembers under the floor ## Posts, rails and skin A side impact on a box body rarely damages only what is visible. The post takes the load, deforms, and pulls at its connections to the top rail and the bottom rail. Skin splits along the rivet or fastener line. Repair therefore starts by removing skin over the affected bays so the frame members can be inspected directly. Deformed posts get cut out and replaced with matching section, and the rail connections get rebuilt with correct fastening rather than reused holes. Skin replacement varies with the body type. Aluminum sheet over posts gets replaced panel by panel with fresh fasteners into sound material and seam sealing at the laps. Fiberglass reinforced panel bodies get scarfed and bonded sections where the core is intact, or full panel replacement between posts where it is not. Either way, the finished surface has to be flat enough that a lettered graphic does not telegraph the repair. - Skin removed to inspect posts and rails directly - Deformed posts replaced with matching section - Rail connections rebuilt with new fastening - Laps seam sealed on aluminum skinned bodies - Surface flatness checked before lettering goes back ## Rear frame, roll up door and threshold The rear frame is the most abused part of a box truck. Forklift tines, pallet jacks, dock plates and impatient backing all hit the same twelve inches of structure. The frame gets bent, the door track distorts at the bottom, and the threshold plate lifts. Once the track is out of alignment the door binds at the bottom of its travel, and drivers force it, which bends slats and elongates hinges further up the curtain. Repair works from the frame outward. The rear frame gets straightened or sectioned with matching extrusion, the track is replaced where it is deformed, and the threshold plate is rebuilt and fastened into sound structure. Then the door itself gets attention: individual slat replacement, hinge and roller replacement as a set, and torsion spring adjustment or replacement to suit the door weight. The door is cycled repeatedly before the truck is released. ## Floors, liftgates and interior protection Box truck floors are usually hardwood strips or laminated plywood over steel or aluminum crossmembers. They fail from moisture entering at the rear threshold and from point loading by pallet jack wheels. A soft floor is not just an inconvenience; the floor ties the two sides of the body together at the bottom, so a rotten floor lets the body spread. Replacement removes the covering, treats or replaces corroded crossmembers, and installs new material fastened to a proper schedule. Liftgate mounting is the other structural item. A gate hangs off the rear frame and applies a large moment every cycle. Cracking at the mounting plates and at the frame extension is common on high cycle vehicles. Repair inspects the mounting structure, rebuilds cracked welds with proper preparation, and adds reinforcement where the original arrangement was marginal. Interior scuff band and wall liner repair follows so cargo does not damage the rebuilt structure immediately. - Corroded crossmembers treated or replaced before new flooring - Floor fastened to a schedule that ties the sides together - Liftgate mounting welds inspected and reinforced - Threshold plate rebuilt into sound structure - Interior scuff bands and wall liner restored ## Frequently asked questions ### Is it cheaper to repair the box or replace the body? Repair is usually the better value because box bodies are built from repeatable sections. Replacing three posts and two skin panels costs a fraction of a new body and returns the truck to service faster. Replacement becomes worth considering when the floor, the crossmembers, the rear frame and multiple posts are all compromised at once, which is typically a corrosion story rather than a collision one. ### My roll up door binds near the bottom. What causes that? Almost always a bent track at the lower section, caused by dock or forklift contact. The door runs fine through most of its travel and then catches at the same point, and drivers force it, which bends slats and wears hinges. Repair straightens or replaces the affected track section first, then addresses the slats, hinges and rollers that were damaged by forcing it. ### Can a soft box floor be repaired in sections? Yes, when the crossmembers underneath are sound. Damaged flooring gets cut back to a joint over a crossmember, new material is fitted and fastened, and the seam is detailed so water does not enter it. Where the crossmembers themselves have corroded, they get treated or replaced first, because new flooring fastened to failing structure will move and fail again. ### Do you install and repair liftgate mounting? Mounting structure repair, reinforcement and equipment installation are all in scope, along with the electrical work that feeds the gate. That covers cracked mounting plates, frame extensions, wiring, and the switches and controls associated with the gate. Engine and drivetrain work is not performed, and the estimate states that boundary on every commercial job. --- OCRV Center. 23281 La Palma Ave, Yorba Linda, CA 92887. (949) 799-3387. info@ocrvcenter.com. Serving Eastvale, California in Riverside County, about 20 miles from the shop. All work is performed in shop at the Yorba Linda facility. No mobile, roadside or on-site service is offered. Scope is body, paint, structural, fiberglass, interior and vehicle systems work. Engine rebuilds, transmission rebuilds, drivetrain work, DOT inspections and emission testing are not performed.