# Class C Motorhome Repair for Eastvale, California > Cabover cap repair, cab to house joint sealing, sidewall and slide work on Class C coaches serving Eastvale owners. Source: https://ocrv.info/vehicles/rvs-and-motorhomes/class-c A Class C motorhome builds a house body behind a factory van or truck cab and adds a cabover section above it. Repair work concentrates on the cabover front cap, the cab to house joint, overcab window seals, laminated sidewalls, rear wall separation, entry steps and the electric slide mechanisms these coaches typically use. ## Pricing Typical range $1,000 to $150,000+, 5 to 800+ hours. The defining feature of a Class C is also its most common repair. The cabover section hangs forward over a factory cab, unsupported except where it ties into the house structure behind it. That cantilever moves. Every expansion joint on SR-91 puts a small twisting load into the cabover, and over years those loads open the seam where the cabover cap meets the sidewall skin and the cab roof. Underneath, most Class C units use a cutaway chassis from Ford or Chevrolet with the factory cab left intact and the house body built onto the frame behind it. The junction between a steel cab and a fiberglass and aluminum house is the second recurring problem area. Two different materials with different expansion rates are joined with sealant and a trim strip, and sealant is the part that ages out. Class C coaches are the most common family unit on the road, which means the shop sees them with the widest range of damage. A Class C from Eastvale might arrive with a scraped cabover from a carport beam, a rear wall separating at the corner post, or a soft floor at the dinette where a window has been leaking quietly for a couple of seasons. All of it is handled in shop at the Yorba Linda facility. ## Common damage - Cabover corner cracking - Overcab window leaks - Cab to house joint sealant failure - Dinette floor soft spots - Rear corner post separation - Schwintek slide gear damage - Entry step and door frame damage - Roof to sidewall seam opening ## The cabover: cantilever, cracks and leaks Cabover damage falls into three groups. Impact damage from carports, low branches and parking structures hits the leading edge and the upper corners. Fatigue cracking shows up as fine radiating lines from the corners of the overcab window opening. Water damage appears as a stained ceiling panel or a bunk mattress that stays damp. All three often exist at once because a cracked corner lets water in and the water softens the substrate that was supposed to resist the next flex cycle. Correct repair reads the sequence in reverse. Wet substrate comes out first. The framing behind it, usually aluminum tube or wood depending on the builder, gets inspected and replaced where corroded or rotted. New substrate is bonded, the fiberglass laminate is rebuilt across the crack with a proper scarf rather than a filler skim, and only then does refinish happen. Skipping the substrate step produces a repair that cracks again in the same place within a year. - Radiating cracks at overcab window corners - Leading edge impact from carports and low clearance - Stained cabover ceiling panels and damp bunk bedding - Corroded aluminum tube framing behind wet substrate - Laminate rebuilt with scarf joints, not filler skims ## Where the cab meets the house The cab to house joint carries a trim strip, a sealant bead and often a rubber gasket at the roof line. On a coach that has been through enough heat cycles, the sealant hardens and pulls away from the steel side first because steel and fiberglass expand at different rates. Water then runs down inside the cab pillars and shows up as a wet driver footwell or a corroded seat bracket, which owners rarely connect back to the house body above. Repair means stripping the joint completely rather than adding sealant on top. Old material comes off, both surfaces get cleaned to bare, corrosion at the steel edge gets treated, and a fresh bead goes in with the correct product for a dissimilar material joint. The trim strip gets replaced if it has lost its clamping shape. Where the cab roof has corroded through, panel repair happens before resealing so the joint is bonding to sound metal. ## Slides, rear walls and the back corner Class C slide rooms are commonly Schwintek style rack and pinion units driven by motors in the vertical side tracks. They are compact and they are unforgiving of a room that is not square. Symptoms of a binding room include a motor that stalls on one side, chewed nylon gear teeth in the track, and a room that comes in cocked. Repair starts with squaring the room and checking the wall opening, then addresses the track, gears and controller synchronization. The rear wall is the other weak point. On many Class C bodies the rear wall is a separate panel joined to the sidewalls at corner posts and to the floor at a bottom rail. Rear impacts, ladder loads and years of road spray at the lower edge open those joints. Separation shows as a visible gap at the corner or a rear cap that has started to bow outward. Repair rebuilds the corner post connection and re bonds the panel rather than sealing over a moving gap. - Schwintek track and gear rebuild with controller sync - Room squareness checked before mechanism parts are quoted - Corner post reconstruction at rear wall separation - Bottom rail and floor edge rot repair - Rear ladder mount reinforcement ## Frequently asked questions ### Why does my cabover keep cracking in the same spot? Because the crack is a symptom, not the problem. A repair that fills the crack without addressing wet substrate or damaged framing leaves the structure just as flexible as before, and the fresh laminate is the weakest thing at that location. Lasting repair replaces the compromised backing material, restores the framing, then rebuilds the fiberglass across a wide scarf joint. ### How do I know if the overcab bunk floor is sound? Walk it and press it, then confirm with instruments. Softness underfoot, a spongy feel at the leading edge, a musty smell in the bunk, or staining at the window corners all point to moisture. A moisture meter reading through the interior panel gives a number, and an inspection with the ceiling panel dropped gives a definitive answer about framing condition before any repair is priced. ### Can a Schwintek slide be repaired or does the whole system come out? Most Schwintek problems repair in place. Worn nylon gears, damaged track sections, stalled motors and controllers that have lost synchronization are all serviceable items. What has to be corrected first is squareness. If the room is racked or the opening has moved, new gears will strip again. Structural correction comes first, then the mechanism, then a full cycle test. ### Is the cab damage and house damage handled as one repair? Yes, and that is deliberate. Splitting the work between a conventional collision shop for the cab and an RV shop for the house creates a seam nobody owns, usually at the joint that leaks. Both sides are handled at the Yorba Linda facility, with the cab panel work, the house structure and the joint itself addressed in one sequence and one refinish plan. --- OCRV Center. 23281 La Palma Ave, Yorba Linda, CA 92887. (949) 799-3387. info@ocrvcenter.com. Serving Eastvale, California in Riverside County, about 20 miles from the shop. All work is performed in shop at the Yorba Linda facility. No mobile, roadside or on-site service is offered. Scope is body, paint, structural, fiberglass, interior and vehicle systems work. Engine rebuilds, transmission rebuilds, drivetrain work, DOT inspections and emission testing are not performed.